Freight Class Calculator

Freight Class Calculator: Density To NMFC Class (2025 Scale)

Enter a shipment’s dimensions and weight to get its density and class on the 13-tier NMFC density scale in use since July 2025, with NMFTA’s measuring rules.

By the Supply Chain Degree Programs editorial team Updated
A forklift carrying two shrink-wrapped, strapped loads on wooden pallets past a flatbed truck in a muddy yard
Density Tiers Since July 19, 2025
13
FedEx Freight and ABF notices
Cubic Inches In A Cubic Foot
1,728
NMFTA density calculator
Dimensioner Tolerance NMFTA States
±0.5 in
NMFTA density calculator

Freight Class Calculator: The Short Version

  • Since July 19, 2025, density-based items use 13 classes. They run from class 50 for the densest freight to 400 for the lightest.
  • Density is weight divided by cubic feet. Multiply length × width × height in inches and divide by 1,728 to get cubic feet.
  • NMFTA’s example: 450 pounds on a 48 × 40 × 45 inch pallet is 9 pcf. On the 13-tier density scale, that’s class 100.
  • Measure the pallet too. Use the greatest outside dimensions of the unit as shipped.

Freight Class Calculator

Enter each handling unit as it will ship, pallet included. Add a row for each different size; use the count for identical units. The calculator works out total cubic feet, density and the class the current density scale gives it. Nothing you type leaves this page.

How Freight Class Works

Freight class is how less-than-truckload (LTL) carriers in the US sort freight for pricing. It comes from the National Motor Freight Classification, the NMFC, which the National Motor Freight Traffic Association (NMFTA) publishes. NMFTA assigns classes from 50 to 500 on four characteristics: density, handling, stowability and liability.

Density does most of the work for most freight. NMFTA’s guidebook says a large share of NMFC items are classed by density, which is why a calculator like this one answers the everyday question. The other three characteristics come in when a commodity is hard to handle, hard to load alongside other freight, or easy to damage or steal.

Freight Class By Density: The 13-Tier Scale

Since July 19, 2025, NMFC items classed by density use one 13-tier scale. NMFTA’s public pages don’t print the whole table, so this one comes from two LTL carriers’ notices that print it identically, FedEx Freight’s and ABF’s, and both say it applies “where applicable.” It matches every break point NMFTA itself has published, including its example that “A pallet at 15.0 PCF ships at Class 70, and the same pallet at 14.9 PCF ships at Class 85.” Each range includes its lower bound: exactly 10 pcf is class 92.5. The less a shipment weighs for its size, the higher its class.

Freight class by density in pounds per cubic foot, on the 13-tier NMFC density scale
Density (Pounds Per Cubic Foot)ClassScale
50 or more 50
35 to under 50 55
30 to under 35 60
22.5 to under 30 65
15 to under 22.5 70
12 to under 15 85
10 to under 12 92.5
8 to under 10 100
6 to under 8 125
4 to under 6 175
2 to under 4 250
1 to under 2 300
less than 1 400

FedEx Freight and ABF density scale notices, checked against NMFTA (October 22, 2026). The bar grows with the class: lighter freight for its size, higher class.

The Freight Class Formula, Step By Step

  1. Measure the length, width and height of the handling unit in inches.
  2. Multiply them for cubic inches, and divide by 1,728 for cubic feet.
  3. Divide the weight in pounds by the cubic feet. That’s the density in pounds per cubic foot (pcf).
  4. Find the density on the table above.

NMFTA’s own worked example: a 48 × 40 × 45 inch unit is 86,400 cubic inches, or 50 cubic feet. At 450 pounds, that’s 9 pcf, which the density scale puts in class 100. With several handling units, add up the cubic feet and the weights, then divide total weight by total cubic feet. In metric, a kilogram is 2.2046 pounds and an inch is 2.54 centimeters; the calculator converts for you.

How To Measure A Shipment For Freight Class

Measure what the carrier will measure. NMFTA’s rule is to “Use the greatest outside length, width, and height of the finished handling unit,” including any part that sticks out past the rest of the load, and it’s explicit about pallets: “Measure the handling unit as it will be shipped, including the pallet in its outside dimensions and total weight.”

  • Measure to the outside. An overhanging carton sets the dimension, not the pallet edge.
  • Height includes the pallet. Measure from the floor to the highest point of the load.
  • Irregular shapes take their greatest straight-line length, width and height.
  • Several units are measured one by one, then combined as above.

When Density Doesn’t Decide The Class

Density gives a guideline, not a guarantee. NMFTA says plainly that “a PCF result alone cannot tell you the correct item number or class,” and its own calculator “does not certify freight class.” Many NMFC items set their own density ranges for their commodity, and some are classed on handling, stowability or liability instead. To find the item and its exact ranges you need the NMFC, which NMFTA licenses through its ClassIT+ service.

What Carriers Check, And The Tolerances

Carriers can measure freight with dimensioners and weigh it on scales, and a reading that differs from the bill of lading can change the class and the charge. NMFTA’s calculator page notes that dimensioner readings can vary by plus or minus 0.5 inch, and gives scale tolerances by weight:

  • Up to 2,500 pounds: plus or minus 5 pounds
  • Up to 5,000 pounds (above 2,500): plus or minus 10 pounds
  • Up to 10,000 pounds (above 5,000): plus or minus 20 pounds

Measuring the way NMFTA describes, and writing the true dimensions on the bill of lading, is the way to avoid a reclass.

Who Works Out Freight Class For A Living

Classing freight is daily work for freight brokers, logistics coordinators and freight forwarders, who BLS counts together as cargo and freight agents: 97,670 jobs at a median of $52,260 (May 2025). The logistics degree rankings list the programs that teach transportation and freight.

FAQ

What Is The Formula For Freight Class?

Freight class comes from density. Multiply the handling unit’s length, width and height in inches, divide by 1,728 to get cubic feet, then divide the weight in pounds by the cubic feet. Find that density in pounds per cubic foot on the density scale: 9 pcf, for example, falls in class 100.

How Many Pounds Per Cubic Foot Is Class 70?

On the 13-tier density scale in use since July 19, 2025, class 70 covers 15 to under 22.5 pounds per cubic foot. Class 65 starts at 22.5 pcf, and below 15 pcf a shipment falls to class 85.

What Is The Lowest Freight Class?

Class 50, for freight of 50 pounds per cubic foot or more. On the density scale the highest is class 400, for freight under 1 pound per cubic foot; NMFC classes overall run from 50 to 500.

Does The Pallet Count In Freight Class?

Yes. NMFTA’s instruction is to “measure the handling unit as it will be shipped, including the pallet in its outside dimensions and total weight.” The pallet’s height counts toward the unit’s height.

Is Freight Class The Same As The NMFC Number?

No. The NMFC item number identifies the commodity, and the item sets its class, sometimes by density range. The NMFC itself is licensed through NMFTA’s ClassIT+ service; the density formula and NMFTA’s calculator are free.

Sources

  1. 1 NMFTA, How Much Density Margin Does Your Packaging Need? (October 22, 2026): published break points Read .
  2. 2 FedEx Freight, NMFC changes (customer notice, May 2025): 13-tier density scale Read .
  3. 3 ABF Freight (ArcBest), Freight class and NMFC code basics: 13-tier density scale Read .
  4. 4 NMFTA, LTL Freight Density Calculator (formula, measuring rules, tolerances) Read .
  5. 5 NMFTA, Density Best Practices Guidebook Read .
  6. 6 NMFTA, National Motor Freight Classification overview Read .
  7. 7 NMFTA, NMFC Book (licensing) Read .
  8. 8 BLS OEWS, May 2025: Cargo and Freight Agents (SOC 43-5011) Read .

Sponsored

Supply Chain Degree Programs

Schools pay to appear in these listings. They are separate from our rankings, which no school can pay to change.